WMI Stage 1.5 Turbo

Stage 1.5 Turbo: The all-new stage 1.5 water-methanol injection controller from Bosphorus Innovations gives you the benefits of a boost gauge and water-methanol controller/ fail-safe all in one!  The new controller comes with a built-in 10 bar/ 145 psi manifold absolute pressure sensor. That allows you to set water-methanol in desired boost pressure. The injection stage is adjustable to match what the engine requires.

The new white and red dual-tone color LCD screen shows boost, injection, test mode, fault codes, setting response time, resolution, fine adjustment, power saving mode, lock the keys, and output modes in a bright easy to read screen.

Water/ Methanol Injection pump has no pressure cut-off switch for eliminating any oscillation/pulsation. Internally bypasses for a smooth constant even flow at the nozzle.  Our standard water-methanol pump is suitable for up to 1000hp. If you need more than 1260 ml/min or 20 GPH. Please choose the bigger pump and controller.

All metal equipment has the durability to corrosion of methanol and water, which constitute corrosion impact-resistant nickel-plated brass, brass, and EPDM grade plastic material.

All of our products are guaranteed for 2 years against the fabricated problem from the date of receipt by you.

Nozzles have a flow rating of your choice:

95cc / 125cc / 157cc / 189cc /  220cc / 252cc / 283cc / 315cc / 378cc / 378cc / 440cc / 504cc / 567cc / 630cc / 755cc / 880cc / 1000cc / 1130cc / 1260cc / 1575cc / 1890cc / 2200cc

1.5 GPH | 2 GPH | 2.5 GPH | 3 GPH | 3.5 GPH | 4 GPH | 4.5 GPH | 5 GPH | 6 GPH | 7 GPH | 8 GPH | 9 GPH | 10 GPH | 12 GPH | 14 GPH | 16 GPH | 18 GPH | 20 GPH | 25 GPH | 30 GPH | 35 GPH

100% Water:  10-15% Water/ Fuel ratio or 0.5-1cc per HP

%50-50 Water-Methanol: 15-20% W-M/ Fuel ratio or  1-1.5cc per HP

100% Methanol: 20-25% Methanol/ Fuel ratio or 1.5-2cc per HP

Please indicate which nozzle size and color of hose you prefer before the order item. If you don’t specify the size, we will send you a 252 ml/min (4 GPH) nozzle and Red Hose.

Included:

1. High-Pressure Diaphragm pump
2. 2 x 3/8″ NPT – ¼” compression type pump fitting
3. Nozzle
4. 40-micron stainless steel filter
5. Nozzle mounting bung
6. Check valve
7. 1/8″ NPT – ¼” compression type hose fitting
8. Gauge Controller
9. 5mm – 1/4″ elbow hose fitting for gauge
10. 1/4″ Tee for vacuum/ boost source
11. Controller with wiring loom
12. 1,15 Gallon/ 4,6 Quart/ 4,3 Liter plastic tank
13. Plastic tank cap
14. 1/8″ NPT – ¼” compression type tank fitting
15. 20 FT/ 6 meter ¼” OD. injection hose
16. 2*Fully insulated butt cable connector
17. Fully insulated Ground cable connector
18. 5*zip tie
19. 2*screw and 2*washer for tank
20. 4*screw and 4*washer for pump
21. 3d sticker
22. 8,5*4,5cm sticker
23. 2 x 5*2,5cm sticker
24. Installation manual