WMI Stage 1.5+ Turbo LCD

Stage 1.5+ Turbo: The all-new stage 1.5 water-methanol injection controller from Bosphorus Innovations gives you the benefits of a boost gauge and water-methanol controller/ fail-safe all in one!  The new controller comes with a built-in 10 bar/ 145 psi manifold absolute pressure sensor. That allows you to set water-methanol in desired boost pressure. The injection stage is adjustable to match what the engine requires.

The new white and red dual-tone color LCD screen shows boost, injection, test mode, fault codes, setting response time, resolution, fine adjustment, power saving mode, lock the keys, and output modes in a bright easy to read screen.

Water/ Methanol Injection pump has no pressure cut-off switch for eliminating any oscillation/pulsation. Internally bypasses for a smooth constant even flow at the nozzle.  Our standard water-methanol pump is suitable for up to 1000hp. If you need more than 1260 ml/min or 20 GPH. Please choose the bigger pump and controller.

The new integrated solenoid valve and the nozzle assembly offer 100% safety for all injection systems utilizing a rear-mounted reservoir, injection points under vacuum, or installs where the injection nozzle is lower than the water-methanol reservoir. The solenoid fits nozzle between the pump and injection point and locks fluid in place when not in use adding safety and peace of mind to any injection system. The solenoid mounted nozzle works as an injector style. Because the reaction time is fast.

All metal equipment has the durability to corrosion of methanol and water, which constitute corrosion impact-resistant nickel-plated brass, brass, and EPDM grade plastic material.

All of our products are guaranteed for 2 years against the fabricated problem from the date of receipt by you.

Nozzles have a flow rating of your choice:

95cc / 125cc / 157cc / 189cc /  220cc / 252cc / 283cc / 315cc / 378cc / 378cc / 440cc / 504cc / 567cc / 630cc / 755cc / 880cc / 1000cc / 1130cc / 1260cc / 1575cc / 1890cc / 2200cc

1.5 GPH | 2 GPH | 2.5 GPH | 3 GPH | 3.5 GPH | 4 GPH | 4.5 GPH | 5 GPH | 6 GPH | 7 GPH | 8 GPH | 9 GPH | 10 GPH | 12 GPH | 14 GPH | 16 GPH | 18 GPH | 20 GPH | 25 GPH | 30 GPH | 35 GPH

100% Water:  10-15% Water/ Fuel ratio or 0.5-1cc per HP

%50-50 Water-Methanol: 15-20% W-M/ Fuel ratio or  1-1.5cc per HP

100% Methanol: 20-25% Methanol/ Fuel ratio or 1.5-2cc per HP

Please indicate which nozzle size and color of hose you prefer before the order item. If you don’t specify the size, we will send you a 252 ml/min (4 GPH) nozzle and Red Hose.

Included:

1. High-Pressure Diaphragm pump
2. 2 x 3/8″ NPT – ¼” compression type pump fitting
3. Nozzle
4. 40-micron stainless steel filter
5. Nozzle mounting bung
6. Solenoid valve
7. 1/8″ NPT – ¼” compression type hose fitting
8. Gauge Controller
9. 5mm – 1/4″ elbow hose fitting for gauge
10. 1/4″ Tee for vacuum/ boost source
11. Controller with wiring loom
12. 1,15 Gallon/ 4,6 Quart/ 4,3 Liter plastic tank
13. Plastic tank cap
14. 1/8″ NPT – ¼” compression type tank fitting
15. 20 FT/ 6 meter ¼” OD. injection hose
16. 2*Fully insulated butt cable connector
17. Fully insulated Ground cable connector
18. 5*zip tie
19. 2*screw and 2*washer for tank
20. 4*screw and 4*washer for pump
21. 3d sticker
22. 8,5*4,5cm sticker
23. 2 x 5*2,5cm sticker
24. Installation manual